Tenere 700 tail tidy: B&B Off-Road Engineering

As with many Japanese bikes, the Tenere 700 comes with an OEM monstrosity of a number plate holder hanging far past the tail light and adorned with chinzy reflectors, where it's readily exposed to breakage on your first tip-over in the woods. As with my WR250R, one of the first mods to my Tenere has been to show that booty some love and install a tail tidy. 

Now that the Tenere 700 has been out for a year, those of us in North America who are now just getting the bike can benefit from a wide range of tail tidy options. CamelADV, Adventure Spec, Rally Raid UK, and R&G all offer some good options. 

But the one I chose comes from B&B Off Road Engineering out of Australia, where there's a solid Tenere 700 following and some of the hardest-core riders of this bike in the world right now. I chose B&B's tail tidy because it offers a solid reinforced mechanical design, it doesn't require cutting the OEM plastics, and it has a good fit and finish and a decent sealed LED plate light. Mine was the first to be delivered to Canada, and having received it only 10 days after placing my order, I installed it right away in one evening. 

For Canadians considering the B&B option, I recommend ordering direct from Australia because factoring in the exchange rate and $30 of duties, it ends up significantly cheaper (and probably faster) than ordering from B&B's US distributor. plus I had excellent service from Sarah at B&B, who was quick to let me know when shipping to Canada was re-opened following the COVID shutdown. Go Commonwealth! 

All the parts come nicely bubble-wrapped. The included hardware is mostly metric stainless steel. I replaced some of the nuts with stainless locknuts (M5). 

What's in the box

The tidy is made from aluminum, doubled in places with welded reinforcements. The whole thing is coated in a thick optional black finish (standard is silver) that looks like it should withstand significant abuse.

Here you can see the reinforcement plate for the turn signal stalk. B&B has an optional insert to allow you to install round, threaded signal mounts, which I plan to adopt when I can order some LED signals. 

This is the top plate that bolts into your subframe. Again, beefy construction. 

The number plate light is a completely sealed LED unit. Looks to be decent quality for both the plastics and wiring.

I like how the metal wiring cover reinforces the structure of the number plate holder. There's no flex in this system, so I don't expect any metal fatigue cracking. 

B&B includes easy to follow instructions to remove the OEM tail assembly. The Tenere 700 is so easy to work on... all the bolts are easily accessible and all you need are 8mm and 10mm sockets and a 4mm and 5mm hex to remove the body panels. Make sure you label your turn signals so you know which side to install them on--the wiring only connects one way! 

Installation is a breeze. To connect the number plate light, I cut off the OEM connector and spliced it into the B&B wiring with some heat-shrink tubing and electrical tape to reseal the harness cover. Connect the white and black wires together (ground) and brown and blue together (+12V). Check your wiring by turning on the key before putting everything back together.

When installing the tail tidy wiring cover, I had a bit of a challenge threading in the 10mm cap screws provided in the kit because of some minor deformation of the aluminum and plastic coating on the aluminum threads. One bolt went in fine, but the metal on the other side of the cover was lifted up a bit and the short fastener wouldn't quite reach. I used a longer bolt to clean out the threads and wind things in with all fasteners installed loosely, then replaced the long bolt with the correct shorter one. It's really not that fussy though, and it all went together fine. Fit overall is excellent and no filing or drilling was required except to mount a reflector bracket (see below) and my number plate (no holes are provided). 

Here's all the crap left over. Easily a couple of pounds of plastic and metal! 

One thing the B&B kit is missing is a way to attach a rear reflector. I made a simple bracket out of some scrap stainless steel and sprayed it black with Krylon paint. Last thing I want is to get hassled (or worse)  during a police stop because I'm missing a required reflector! 

This is the OEM reflector bolted on. I drilled three holes in the B&B number plate holder to attach the bracket using some stainless steel bolts. 

There's nowhere to attach side orange reflectors, but what's neat is that even when you remove the OEM plastics, Yamaha has thoughtfully included knurled handgrips under the outer handgrips for the pillion passenger. The flat area right above the grips is a perfect spot to attach some 3M reflective tape. The tape is flush to the surface and therefore protected, yet provides a wide view of 10 square inches of reflector per side, versus the 3 square inches provided by the OEM round reflectors per side. A good conspicuity upgrade in my mind! 

One last note is that the brake light has a small bit of foam stuck to the bottom where it contacted the OEM plastics. When you've installed the B&B kit, this foam doesn't touch anything. I peeled it off and reattached it further inboard so it wedged between the light and the B&B plate. While it doesn't look like the tail light will move around much on rough terrain, repositioning the foam adds a little bit of extra vibration protection.

Overall I'm very pleased with this kit. It's easy to install (couple of hours), solidly built, and looks great. With the addition of a rear reflector and the side tape, I see no reason why the bike shouldn't meet the same regulatory requirements as the OEM configuration.